Speedhut 2002-2007 Subaru Impreza_WRX_STi Triple Dash Pod Manuel d'utilisateur télécharger pdf

Please contact Speedhut service department If you have a problem with this Product.

Speedhut Inc. 165 North 1330 West B2, Orem, Utah 84057 | [email protected] | (801) 221-1460 (9am - 5pm MST) | www.Speedhut.com

Please contact Speedhut service department If you have a problem with this Product.

Speedhut Inc. 165 North 1330 West B2, Orem, Utah 84057 | [email protected] | (801) 221-1460 (9am - 5pm MST) | www.Speedhut.com

Model# 20018

1. Remove factory clock per manufacturer’s instructions. Contact auto manufacturer for details.

2. Position dash pod in the desired mounting location to mark where hole will be drilled in left rear flange. Using a 1⁄4” drill bit,

drill hole in left rear flange to match existing hole in right rear flange.

3. Install clips.

4. Install the gauges in the dash pod and run wiring using one of the two options below:

Option 1: Run wiring out the back of the pod through the pre-molded wire channel, down the back of the dashboard, and

through the firewall.

Option 2: Make a small hole in the dash underneath the Dash Pod, and run wiring down and out though the firewall.

5. Use included hardware to secure the Dash Pod to the top of the dashboard. Replace factory clock.

NOTE: Due to normal manufacturing processes you may have “flashing” (small fibers of plastic) around the pod holes.

Once the gauge(s) are installed in the pod you will not be able to see the “flashing.”

Installation Instructions: Subaru Impreza/WRX/STi 02-07 - Triple Dash Pod

Model# 20018

1. Remove factory clock per manufacturer’s instructions. Contact auto manufacturer for details.

2. Position dash pod in the desired mounting location to mark where hole will be drilled in left rear flange. Using a 1⁄4” drill bit,

drill hole in left rear flange to match existing hole in right rear flange.

3. Install clips.

4. Install the gauges in the dash pod and run wiring using one of the two options below:

Option 1: Run wiring out the back of the pod through the pre-molded wire channel, down the back of the dashboard, and

through the firewall.

Option 2: Make a small hole in the dash underneath the Dash Pod, and run wiring down and out though the firewall.

5. Use included hardware to secure the Dash Pod to the top of the dashboard. Replace factory clock.

NOTE: Due to normal manufacturing processes you may have “flashing” (small fibers of plastic) around the pod holes.

Once the gauge(s) are installed in the pod you will not be able to see the “flashing.”

Installation Instructions: Subaru Impreza/WRX/STi 02-07 - Triple Dash Pod

Résumé du contenu

Page 1

Please contact Speedhut service department If you have a problem with this Product. Speedhut Inc. 165 North 1330 West B2, Orem, Utah 84057 | support@s

Commentaires sur ces manuels

Pas de commentaire

Speedhut 2002-2007 Subaru Impreza_WRX_STi Triple Dash Pod Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Speedhut 2002-2007 Subaru Impreza_WRX_STi Triple Dash Pod. Speedhut 2002-2007 Subaru Impreza_WRX_STi Triple Dash Pod User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Speedhut 2002-2007 Subaru Impreza_WRX_STi Triple Dash Pod