Speedhut Freedom CAN-bus Gauge Installation Manuel d'utilisateur télécharger pdf

Freedom CAN-bus Gauge Instructions

Ground (black)

+12 volts Dash lighting (white)

Snap connection

for dial lighting

+12 Volts keyed ignition

(Red)

(Black)

Ground

(White)

+12 Volts Dash lighting

Power distribution cable to plug all gauges into

(green with yellow)

(green with red)

(blue with white)

**left turn signal +12V pulse

**right turn signal +12V pulse

**high beam wire +12V

Inverter

E18-686-5CR

C01-18N-2

C11-18A01

Note: Tie together the

+12volt dash lighting white

wire to the +12 volt inverter

white wire and connect to

the same dash lighting

source.

Turn signals and High Beam Indicator (if applicable)

Figure 1: Gauge Power and Lighting Setup

Figure 2: OBDII and Daisy Chain Setup

Note: A set of Freedom CAN-bus

Gauges can be daisy chained

together in any order.

Daisy Chain Jacks

CAUTION: Do not connect the Daisy Chain while

connected to a powered OBDII system.

Failure to do so will throw a check engine code.

RED

BLA

To OBDII connector

or wire it direct to

CAN high and

CAN low ECU lines.

CAN high

OBDII

CAN low

OBDII Option:

Wire Direct Option:

Does your vechicle support the CAN-BUS protocol?

1. Disconnect negative (-) battery cable

2. Hook up power requirements as shown in Figure 1.

3. Daisy Chain the gauges together with Stereo Cables.

(Gauges can be daisy chained in any order. See Figure 2)

CAUTION: Do not connect the Daisy Chain while connected to a

powered OBDII system. Failure to do so will throw a check engine

code.

4. Mount gauge(s) for easy viewing. Use spin lock ring (included)

to mount to panel.

5. Reconnect negative (-) battery cable.

(sold seperatly)

Included in Gauge Set only (sold seperatly)

GF-HRNS-06

GF-HRNS-07

Wire Direct Note: Speedhut Freedom CAN-BUS gauges

(individual or daisy chained) will not function when

used in conjunction with any other OBDII device. Cycle

the gauge power to restore proper gauge function.

WARRANTY - Speedhut inc. warrants to the consumer for a period of 5 years from the date of purchase that the product will be free from defects in materials or workmanship.

Speedhut warrants to the consumer for a "LIFE-TIME" that the gauge circuit board will be free from defects in materials or workmanshipPlease contact Speedhut service dept.

If you have a problem with this gauge. suppo[email protected]

INVERTER IS REQUIRED FOR GAUGE DIAL LIGHTING

(Main gauge power)

(Pointer (needle) lighting)

(Gauge Dial lighting)

Note: E18-686-5CR is single gauge inverter to light single gauge

C01-18N-2 & C11-18A01 are multiple gauge lighting inverters that can light

up to 6 - 8 gauges depending on inverter model.

Power Draw = 0.2 Amp

5 Amp Inline Fuse Recommended

for +12 Keyed Ignition

OBDII CAN (J1979) protocol Pinout:

If the vehicle has wires that connect to pins 6 and 14 of the

OBDII connector then the vehicle supports the CAN-BUS

(J1979) protocol.

Pin 4 -- Chassis Ground

Pin 5 -- Signal Ground

Pin 6 -- CAN High (data)

Pin 14 -- CAN Low (data)

Pin 16 -- +12volt Battery power (not for use as gauge power)

Vehicle’s OBDII connector pin numbering

1 2

Résumé du contenu

Page 1 - CAN high

Freedom CAN-bus Gauge InstructionsGround (black)+12 volts Dash lighting (white)Snap connectionfor dial lighting+12 Volts keyed ignition(Red)(Black)Gro

Page 2 - Speed Calibration

Freedom CAN-bus Speedometer Functions000000000000MIMIOdometer (shows up to 999,999 miles or kmh) Trip Odometer (shows up to 99,999.9 miles or kmh)Pres

Commentaires sur ces manuels

Pas de commentaire

Speedhut Freedom CAN-bus Gauge Installation Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Speedhut Freedom CAN-bus Gauge Installation. Speedhut Freedom CAN-bus Gauge Installation User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Speedhut Freedom CAN-bus Gauge Installation